Install the Impossible Progressive Fork Springs On Your FI Vulcan

Nomad FI Progressive Fork Spring Installation


Rating: 0.00/5 (0 votes cast)

Ok I know Progressive dose not make springs for the Fuel Injected Nomad because it’s a cartridge fork system. Well I figured out how to install them. The results are great. The installation is a little more difficult then the regular non-cartridge system but it’s not too difficult. I’d say install time is about 2 hours including some down time while draining springs and forks.

Thanks to Big Al deCoudres

What You'll Need:

  • Parts:
    • Progressive 11-1145 Springs with a 1” Spacer
  • Tools I used are as follows:
    • Small Flathead screwdriver
    • 3-½ ton floor jack, or any jack that will safely lift the front tire at least 10” off the ground.
    • 17 mm Allen wrench or 17 mm nut and a 17 mm socket wrench
    • Air impact wrench, Just makes removing the fork seal caps a lot easier
    • 6 mm Allen wrench
    • 8 mm Allen wrench
    • 14 mm open end wrench
    • 12 mm socket
    • Torque Wrench
    • Bar Clamp
    • Ratchet tie down
    • Masking Tape or electrical tape
    • 1 Qt 15w Fork Oil
    • Light gauge wire (18-22) about 7 feet
    • Small tape measure
    • 2 Moving blankets

How to Do It

Before starting this job you may want to purchase 2 sets of brake pads for the front brakes, as it’s a good time to replace them if needed.

Start by covering your tank and front fender with blankets

Remove dust caps with small flathead screwdriver

Brake Loose the fork caps with a 17 mm Allen wrench don’t remove them yet just break the seal, our use a 17 mm nut in a 17 mm socket with a spacer behind it so it sticks ½ way out of the socket. I used an air impact wrench to brake them loose.

Loosen the 6 mm Allen bolts that clamp the top triple tree to the fork tubes.

Loosen the 8 mm Allen bolts that clamp the bottom triple tree to the fork tubes.

Remove the brake cylinders from both sides with a 12 mm socket, swing them over the front crash bar out of the way.

Disconnect the speedometer cable (if you have one) from the wheel.

Jack up the front-end letting the forks slide out of the triple tree.

Unscrew the fork caps from the tubes, then using a 14 mm open-end wrench on the cartridge rod locknut and the 17 mm Allen wrench on the fork cap, remove the fork cap from the cartridge rod.

Remove the stock springs.

Tip the forks down and drain them into a pan or plastic jugs, let drain for about 5 min.

Turn forks back upright and add about 5 oz of new fork oil to each tube. Pump the cartridge rod up and down several times in each fork to flush out the old oil in the bottom of the cartridge. Drain tubes again.

With the tubes upright and vertical and inserting a tape measure 5 ½ inches into the fork add new fork oil until it comes up to the bottom of the tape measure. Repeat in the other tube.

Lift the cartridge rods up and tie about 3 ½ feet of wire to each rod just below the 14 mm locking nut. Wind up the wire and loosely stuff it in the top of the fork tubes.

Reinstall the forks into the triple trees, tighten up the bottom 8 mm tree clamps and the top 6 mm tree clamps.

Cover the top triple tree with tape around the tube holes to avoid scratching the tree.

Nomad ProspringPull the loose end of the wires tied to the cartridge rods up through the new springs, then the washer, then the spacer.

prospring_nomad_006With the forks fully extended install a bar clamp from the underside of the bottom triple tree to the top side of the top triple tree, on the top tree cover the edge of the fork hole with the clamp and tighten the clamp. This will compress the spring and allow you to attach the fork cap to the connecting rod in the next step.

prospring_nomad_008Now install a ratchet tie down, attach the tie down hook to the disk brake disk, now run the strap over the handlebars and attach the other hook back down to the disc. Tighten the tie down, this will compress the front end, compress it till it is close to bottoming out make sure the spring spacer is being held down by the bar clamp.

prospring_nomad_010.jpgOnce compressed you can Slowly use the wire to pull the cartridge rod up through the washer and spacer. You may need to use a flat head screwdriver to work the connecting rod lock nut through the washer.

Screw the fork cap to the connecting rod. Now use a 14 mm open-end wrench and the 17 mm Allen wrench to tighten the lock nut to the connecting rod.

Now remove the wire used to lift the rod. Release and remove the barclamp.

Slowly release the tie down allowing the forks to fully extend.

Remove the tape.

The cap should now be in the top of the tube, ready to screw in with the 17 mm Allen wrench, if so do it, if they are sitting just on the edge of the tube, give the cap a tap with a rubber mallet, it should slip into place, then tighten it.

If your going to change your front brake pads, now is a good time to do it, then reinstall brake cylinders and tighten bolts to 24 ft lbs.

Reinstall speedometer cable if you have one, and let jack down.

Reinstall plastic chrome fork tube cap covers.

Loosen Allen bolts on top and bottom triple trees and make sure forks are even in height, both of the plastic chrome fork cap covers should extend a little above the top triple tree. At this point I use a rubber mallet to hit the top of the triple tree a few times to make sure the fork tubes are set all the way up in the triple tree.

Tighten top and bottom Allen bolts on triple tree clamps.

Pump front brake lever to bring brakes back up.

Check all bolts to make sure they’re tight.

Remove blankets.

Check everything again.

Put on protective gear including helmet for test ride…..Always a good ideal after working on any critical components like brakes, wheels etc. to where more protection than usual in case something was missed or done wrong.

I’m not a professional wrench, just a shade tree guy. If you decide to use these directions please be advised I may not know what the heck I’m talking about and do the procedure entirely at your own risk like I have. I hope this process works for you, if you try it let me know how it went.

Big Al deCoudres
VROC # 4500
[email protected]

Tag: forks

Share It

Be the first to comment